The RBEF-S Slurry High frquency Magnetic flow converter of this type flowmeter uses 25Hz ~ 50Hz high-frequency square wave excitation, so that effectively reduces the flow noise. It uses the latest signal processing technology and noise suppression algorithm to achieve a stable measurement, which means Zero-point stability, Low steady-state volatility and fast dynamic response. The sensor has abrasion-resistant lining, which is suitable for the flow measurement of solid-liquid suspension or inhomogeneous liquids. RBEF-S is mainly used for measuring the slurry of pulp, coal water slurry, mud (including micro particles) and cement slurry etc.
Slurry Electromagnetic Flow Meter Features:
Slurry Magnetic Flow Meter Specification:
|
|
Slurry Magnetic Flow Meter Model Selection:
RBEF Electromagnetic Flow Meter Model Selection | ||||||||||||||||||
RBEF | ||||||||||||||||||
[1] | [2] | [3] | [4] | [5] | [6] | [7] | [8] | [9] | [10] | [11] | [12] | [13] | [14] | |||||
[1] | Category | Grounding & Lining Protection | ||||||||||||||||
F | Flanged | C | Ceramic | Mini | Mini | [6] |
0 | Body-flange grounding (DN15 - DN1200) | ||||||||||
W | Wafer-type | S | High-Frequency | Ex | Ex-proof | 1 | Ground ring [or lining protection flange] (DN15-DN250) | |||||||||||
L | Threaded | B | Battery-Powered | I | Insertion | 2 | Grounding electrode (DN25 - DN1200) | |||||||||||
K | Clamping | Hp | High-pressure | H | Energy | 3 | Import protection flange (DN50 - DN300) | |||||||||||
[2] | Nominal Diameter(mm) | Ambient Temperature | ||||||||||||||||
003 | 065 | 400 | [7] | A | ≤80 ℃ (All lining) | |||||||||||||
006 | 080 | 450 | B | ≤120 ℃ (Only Neoprene、PTFE、PFA) | ||||||||||||||
010 | 100 | 500 | C | ≤180 ℃ (Only PTFE) | ||||||||||||||
015 | 125 | 600 | Protection& Anti-hazard Requirement | |||||||||||||||
020 | 150 | 700 | [8] |
1 | IP65 | |||||||||||||
025 | 200 | 800 | 2 | IP67 (Only compact) | ||||||||||||||
032 | 250 | 900 | 3 | IP68 (Only remote,tie cable should be specified) | ||||||||||||||
040 | 300 | 102 | 4 | IP65+Ex d ib mb IIC T4 Gb | ||||||||||||||
050 | 350 | 122 | Sensor And Converter Combination Structure | |||||||||||||||
E.g. :050 = DN50; 150 = DN150; 122 = DN1200 | [9] | C | Compact(Only DN15-DN1000) | |||||||||||||||
[3] | Nominal Pressure& Process Connection | R | Remote(With 10m signal cable, the other length is set separately) |
|||||||||||||||
02 | 0.25 MPa (DN700-DN1200) | |||||||||||||||||
06 | 0.6 MPa (DN700-DN1200) | Power Supply | ||||||||||||||||
10 | 1.0 MPa (DN200-DN1200) | [10] | A | Alternating current (85-265) VAC /(45-63)Hz | ||||||||||||||
16 | 1.6 MPa (DN15-DN600) | D | Direct current (16-36) VDC | |||||||||||||||
20 | ANSI 150 (DN15-DN600) | B | Battery 3.6 VDC | |||||||||||||||
40 | 4.0 Mpa (DN 3-DN150) | Output Signal & Input Signal | ||||||||||||||||
50 | ANSI 300 (DN15-DN600) | [11] | 0 | Basic configuration (Current output + pulse output + alarm output) |
||||||||||||||
91 | JIS 10K (DN15-DN600) | |||||||||||||||||
92 | JIS 20K (DN15-DN600) | 2 | Basic configuration + RS232 | |||||||||||||||
93 | Fixed-length model AMAG- I | 4 | Basic configuration + RS485 | |||||||||||||||
94 | Pluggable Model AMAG- I-500 | M | Basic configuration + MODBUS | |||||||||||||||
95 | Pluggable Model AMAG- I-900 | H | Basic configuration + HART | |||||||||||||||
99 | Special pressure requirements(According to special order form) |
P | Basic configuration + Profibus-DP | |||||||||||||||
Additional Function | ||||||||||||||||||
[4] | Lining Material | [12] | O | No requirement | J | Relay output | ||||||||||||
1 | Soft Neoprene (≤ DN1200) | T | Power-off recording | F | Enhancements | |||||||||||||
2 | Hard Neoprene (≤ DN1200) | Q | Quantitative control | S | High-Frequency | |||||||||||||
3 | PTFE (≤ DN1000) | R | Infrared remote control | G | GPRS communication | |||||||||||||
4 | Polyurethane (≤ DN300) | H | Hourly accumulation | L | Ultralow temperatureconverter | |||||||||||||
5 | PFA (≤ DN250) | Factory Inspection (Accuracy Level & Flow Point Number) | ||||||||||||||||
6 | F46 (≤ DN250) | [13] | 1 | 0.5 level、3 point check | 3 | 0.5 level、5 point check | ||||||||||||
7 | Ceramics (≤ DN250) | 2 | 0.2 level、3 point check | T | Other requirement | |||||||||||||
[5] | Electrode Material | Supplementary | ||||||||||||||||
1 | Stainless steel [316L] | [14] |
0 | No requirement | ||||||||||||||
2 | Hastelloy C [Alloy-C22] | 1 | Stainless steel 304SS sensor(304SS flange) | |||||||||||||||
3 | Hastelloy B [Alloy-B10] | 2 | Special requirements 1 (According to special order form)* | |||||||||||||||
4 | Titanium | 3 | Special requirements 2 (According to special order form) ** | |||||||||||||||
5 | tantalum | Selection E.g. | ||||||||||||||||
6 | Platinum/iridium Alloy | Flange type, DN150, 4 .0MPa, PTFE lining, Hastelloy alloy C electrode, body flange grounding, ambient temperature < 120℃, IP65 non-ex-proof,compact,AC power supply, basic configuration + RS485, no additional functional requirements, 0.5 level,3 point check, stainless steel sensor .Selection coding:RBEF-F15040320B1CA4011 |
||||||||||||||||
7 | Stainless steel coated tungsten carbide | |||||||||||||||||
8 | Special conductive ceramics (Only for ceramic lining ) | |||||||||||||||||
* | E.g. :[14]=2,Marked 316SS flange, 304SS sensor shell. | |||||||||||||||||
** | E.g. :[14]=3, Marked 316SS flange, 304SS sensor shell. |
RBEF-S Slurry Magnetic Flow Meter Applications:
Magmeters
Ultrassonic Flow Meter
Coriolis, Thermal Mass Flow Meter
Other Process Instrument